View NX5DV4885EHF_2836234.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1. general description the nx5dv4885e is a dual supply 1-to-2 vga switch. it integrates high-bandwidth spdt switches with level translating switches and level tr anslating buffers to provide switching of input rgb signals and switch ing and level translation of input ddc signals to either of two output channels as well as level translation of input h-sync and v-sync signals the nx5dv4885e is characterized for operation from ?40 ? cto+85 ? c. 2. features and benefits ? rgb switches: ? low on resistance (4 ? typical) ? low on capacitance (12 pf typical) ? low output skew (50 ps) ? low power consumption (< 2 ? a) ? level translation of sync and ddc signals ? over-voltage tolerant inputs ? esd protection: ? hbm jesd22-a114f class 3a exceeds 4 kv ? mm jesd22-a115-a exceeds 200 v ? cdm jesd22-c101d exceeds 1000 v ? iec61000-4-2 contact discharge exceeds 4 kv for i/os ? latch-up performance exceeds 100 ma per jesd78 class ii level a ? specified from ? 40 ? cto+85 ? c 3. applications ? notebook computers ? docking stations ? digital projectors ? computer monitors ? servers ? storage nx5dv4885e dual supply 1-of-2 vga switch rev. 2 ? 4 november 2011 product data sheet
nx5dv4885e all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 4 november 2011 2 of 20 nxp semiconductors nx5dv4885e dual supply 1-of-2 vga switch 4. ordering information 5. marking [1] the pin 1 indicator is located on the lower left corner of the device, below the marking code. 6. functional diagram table 1. ordering information type number package temperature range name description version NX5DV4885EHF ? 40 ? cto+85 ? c hvqfn24 plastic thermal enhanced very thin quad flat package; no leads; 24 terminals; body 4 ? 4 ? 0.85 mm sot616-3 table 2. marking codes type number marking [1] NX5DV4885EHF x5e fig 1. logic symbol 001aao279 r0 r1 g0 g1 b0 en sel b1 g2 b2 sda1 scl1 sda2 scl2 sda0 scl0 control logic level translating switch r2 h0 v0 v1 h1 v cc(a) v cc(b) level translator
nx5dv4885e all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 4 november 2011 3 of 20 nxp semiconductors nx5dv4885e dual supply 1-of-2 vga switch 7. pinning information 7.1 pinning 7.2 pin description (1) this is not a supply pin, the substrat e is attached to this pad using conductive die attach material. there is no electrical or mechanical requirement to solder this pad however if it is so ldered the solder land should remain floating or be connected to gnd. fig 2. pin configuration sot616-3 (hvqfn24) 001aao280 nx5dv4885e transparent top view b2 b0 h0 b1 g0 g2 r0 g1 scl0 r2 sda0 r1 v0 v cc(b) v cc(a) gnd h1 v1 sel en sda1 sda2 scl1 scl2 terminal 1 index area 6 13 5 14 4 15 3 16 2 17 1 18 7 8 9 10 11 12 24 23 22 21 20 19 gnd (1) table 3. pin description symbol pin description r0, g0, b0 3, 4, 5 rgb input or output gnd 10 ground (0 v) v cc(a) 9 supply voltage a h0 6 horizontal sync input v0 7 vertical sync input en 23 enable input (active high) sda0 1 sda0 input or output scl0 2 scl0 input or output sda1, sda2 22, 21 sda input or output scl1, scl2 20, 19 scl input or output v cc(b) 8 supply voltage b v1 12 vertical sync output h1 11 horizontal sync output r1, g1, b1, r2, g2, b2 18, 16, 14, 17, 15, 13 rgb input or output sel 24 select input
nx5dv4885e all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 4 november 2011 4 of 20 nxp semiconductors nx5dv4885e dual supply 1-of-2 vga switch 8. functional description the nx5dv4885e integrates high-bandwidth spdt switches, level-translating buffers and level translating spdt switches to provide a complete solution for 1-to-2 switching of vga signals. an enable input (en) is used to enable or disable the device and a select input (sel) is used to determine which output is selected. when en = low the device is disabled; all switches will be of f and h1, v1 will be forced low. 8.1 rgb switches the nx5dv4885e provides three identical single pole double throw high-bandwidth switches to route standard vga rgb signals (see ta b l e 4 ). 8.2 h-sync/v-sync level translator the horizontal and vertical sy nchronization buffers have inputs (h0, v0) referenced to v cc(a) and outputs (h1 and v1) that are referenced to v cc(b) . this allows level translation of synchronization signals from as low as 2.0 v up to 5.5 v and supports low-voltage cmos or ttl-compatible graphic s controllers meeting the v esa specification for output drive of ? 8 ma. the en input also controls the level shifter (see ta b l e 5 ). table 4. function table rgb h = high voltage level; l = low voltage level; x = don?t care. input switch en sel h l r0 to r1; g0 to g1; b0 to b1 h h r0 to r2; g0 to g2; b0 to b2 l x switches rn, gn, bn off table 5. function table hv h = high voltage level; l = low voltage level; x = don?t care. input switch en h h1 = h0; v1 = v0 lh1, v1 = l
nx5dv4885e all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 4 november 2011 5 of 20 nxp semiconductors nx5dv4885e dual supply 1-of-2 vga switch 8.3 display-data channel multiplexer the nx5dv4885e provides two identical spdt ac tive-level translating switches to route ddc signals (see ta b l e 6 ). the switch outputs are limited to a diode drop below the voltage applied on v cc(a) . to provide vesa i 2 c-compatible signals 3.3 v should be applied to v cc(a) . if voltage translation is not required v cc(a) should be connected to v cc(b) . 9. limiting values [1] the minimum input voltage rating may be exceeded if the input current rating is observed. [2] for hvqfn24 package: above 134.5 ?? c the value of p tot derates linearly with 19.3 mw/k. table 6. function table ddc h = high voltage level; l = low voltage level; x = don?t care. input switch en sel h l sda0 to sda1, scl0 to scl1 h h sda0 to sda2, scl0 to scl2 l x switches sdan, scln off table 7. limiting values in accordance with the absolute maximum rating system (iec 60134). voltages are referenced to gnd (ground = 0 v). symbol parameter conditions min max unit v cc(a) supply voltage a ? 0.5 +6 v v cc(b) supply voltage b ? 0.5 +6 v v i input voltage [1] ? 0.5 +6 v v sw switch voltage [1] ? 0.5 +6 v i ik input clamping current v i < ? 0.5 v ? 50 - ma i sk switch clamping current v i < ? 0.5 v ? 50 - ma i ok output clamping current v o <0v ? 50 - ma i o output current v o =0vtov cc(b) - ? 50 ma i cc supply current i cc(a) or i cc(b) - 100 ma i gnd ground current ? 100 - ma i sw switch current v sw > ? 0.5 v or v sw < 6 v; source or sink current - ? 30 ma v sw > ? 0.5 v or v sw < 6 v; pulsed at 1 ms duration, < 10 % duty cycle; peak current - ? 90 ma t stg storage temperature ? 65 +150 ?c p tot total power dissipation t amb = ? 40 ? cto+85?c [2] - 300 mw
nx5dv4885e all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 4 november 2011 6 of 20 nxp semiconductors nx5dv4885e dual supply 1-of-2 vga switch 10. recommended operating conditions [1] applies to control signal levels. 11. static characteristics table 8. recommended operating conditions symbol parameter conditions min typ max unit v cc(a) supply voltage a 2 3.3 5.5 v v cc(b) supply voltage b 4.5 5.0 5.5 v t amb ambient temperature operating in free-air ? 40 +25 +85 ?c ? t/ ? v input transition rise and fall rate v cc(a) = 2.3 v to 2.7 v [1] -20-ns/v v cc(a) = 3 v to 3.6 v [1] -10-ns/v v cc(a) = 4.5 v to 5.5 v [1] - 5 - ns/v table 9. static characteristics v cc(b) = 4.5 v to 5.5 v; v cc(a) = 2 v to 5.5 v, unless otherwise specified; voltages are referenced to gnd (ground = 0 v) symbol parameter conditions t amb = ? 40 ? cto+85 ?c unit min typ [1] max general i cc(a) supply current a v cc(a) = 3.3 v; en = v cc(a) or gnd; for h1, v1: i o = 0 a --2.0 ? a i cc(b) supply current b v cc(b) = 5.0 v; en = v cc(a) or gnd; for h1, v1: i o = 0 a --2.0 ? a hv buffer v ih high-level input voltage v cc(a) =3vto3.6v 2 - - v v il low-level input voltage v cc(a) =3vto3.6v - - 0.8 v v h hysteresis voltage - 50 - mv i i input leakage current v cc(b) =v cc(a) =5.5v; v i =gndtov cc(a) -- ? 1 ? a v oh high-level output voltage i o = ? 8 ma v cc(b) ? 0.5 --v v ol low-level output voltage i o =8 ma - - 0.5 v i off power-off leakage current v i or v o = 0 v to 5.5 v; v cc(b) = 0 v; v cc(a) = 0 v to 5.5 v -- ? 1 ? a rgb switches i s(off) off-state leakage current v cc(b) = 5.5 v; v i = 0.3 v or 5.5 v; v o = 0 v to v cc(b) ; en = v cc(a) or gnd; see figure 3 -- ? 1 ? a i s(on) on-state leakage current v cc(b) = 5.5 v; v i = 0.3 v or 5.5 v; v o = 0 v to v cc(b) ; en = v cc(a) ; see figure 4 -- ? 1 ? a r on on resistance v i = 0.7 v; i sw = ? 10 ma; see figure 5 and figure 6 [4] -4- ? ? r on on resistance mismatch between channels v i = gnd to 0.7 v; i sw = ? 10 ma [2] -0.5- ? r on(flat) on resistance (flatness) v i = gnd to 0.7 v; i sw = ? 10 ma [3] -0.5- ?
nx5dv4885e all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 4 november 2011 7 of 20 nxp semiconductors nx5dv4885e dual supply 1-of-2 vga switch [1] all typical values are measured at v cc(b) =5v, v cc(a) = 3.3 v and t amb =25 ? c unless otherwise specified. [2] measured at identical v cc , temperature and input voltage. [3] flatness is defined as the difference between the maximum and minimum value of on resistance measured at identical v cc and temperature. [4] guarantees the low level. [5] guarantees the high level. 11.1 test circuits and waveforms c s(off) off-state capacitance - 4.5 - pf c s(on) on-state capacitance - 12 - pf sda, scl i s(off) off-state leakage current v cc(b) = 5.5 v; v cc(a) = 3.6 v; scl0, sda0, scl1, scl2, sda1, sda2 = v cc(a) or gnd; v o = 0 v to v cc(b) ; en = gnd; see figure 3 [5] -- ? 1 ? a r on on resistance v cc(a) =2 v; v i = 0.4 v; i sw = ? 2ma; see figure 5 and figure 7 -9- ? c s(on) on-state capacitance - 15 - pf control logic (sel, en) v ih high-level input voltage v cc(a) = 2.3 v to 2.7 v 1.7 - v v cc(a) = 3.0 v to 3.6 v 2.0 - v v cc(a) = 4.5 v to 5.5 v 0.7v cc(a) -v v il low-level input voltage v cc(a) = 2.3 v to 2.7 v - - 0.7 v v cc(a) = 3.0 v to 3.6 v - - 0.8 v v cc(a) = 4.5 v to 5.5 v - - 0.3v cc(a) v v h hysteresis voltage - 50 - mv i i input leakage current v cc(a) = 5.5 v; v i =gndtov cc(a) -- ? 1 ? a table 9. static characteristics ?continued v cc(b) = 4.5 v to 5.5 v; v cc(a) = 2 v to 5.5 v, unless otherwise specified; voltages are referenced to gnd (ground = 0 v) symbol parameter conditions t amb = ? 40 ? cto+85 ?c unit min typ [1] max x0 refers to r0, g0, b0, scl0 or sda0 x1 refers to r1, g1, b1, scl1 or sda1 x2 refers to r2, g2, b2, scl2 or sda2 fig 3. test circuit for measuring off-state leakage current sel en x0 x1 v ih or v il v cc(a) v cc(b) v ih or v il switch 1 2v il v ih sel v i 001aan176 x2 switch gnd 1 2 v o i s
nx5dv4885e all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 4 november 2011 8 of 20 nxp semiconductors nx5dv4885e dual supply 1-of-2 vga switch x0 refers to r0, g0, b0, scl0 or sda0 x1 refers to r1, g1, b1, scl1 or sda1 x2 refers to r2, g2, b2, scl2 or sda2 fig 4. test circuit for measuring on-state leakage current sel en x0 x1 v ih or v il v cc(a) v cc(b) v ih or v il switch 1 2v il v ih sel v i 001aan177 x2 switch gnd 1 2 v o i s x0 refers to r0, g0, b0, scl0 or sda0 x1 refers to r1, g1, b1, scl1 or sda1 x2 refers to r2, g2, b2, scl2 or sda2 r on = v sw / i sw . fig 5. test circuit for measuring on resistance sel en x0 x1 v il or v ih v cc(a) v cc(b) v ih switch 1 2v ih v il sel v ih v ih en v i v 001aan175 x2 v sw switch gnd 1 2 i sw
nx5dv4885e all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 4 november 2011 9 of 20 nxp semiconductors nx5dv4885e dual supply 1-of-2 vga switch (1) t amb =85 ? c (2) t amb =25 ? c (3) t amb = ?40? c fig 6. on resistance as a function of input voltage (rgb switches) v i (v) 0 1.0 0.8 0.4 0.6 0.2 001aan178 4 6 2 8 10 r on () 0 (1) (2) (3) (1) t amb =85 ? c (2) t amb =25 ? c (3) t amb = ?40? c fig 7. on resistance as a function of input voltage (ddc switches) v i (v) 04 23 1 001aan179 30 15 45 60 r on () 0 (3) (2) (1) (3) (2) (1) v cc(a) = 3.3 v v cc(a) = 5.0 v
nx5dv4885e all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 4 november 2011 10 of 20 nxp semiconductors nx5dv4885e dual supply 1-of-2 vga switch 12. dynamic characteristics [1] all typical values are measured at v cc(b) =5v; v cc(a) = 3.3 v; t amb =25 ? c. [2] t pd is the same as t plh and t phl . [3] guaranteed by design. 12.1 test circuits and waveforms table 10. dynamic characteristics at recommended operating conditions; volt ages are referenced to gnd (ground = 0 v; v cc(b) = 4.5 v to 5.5 v; v cc(a) = 2 v to 5.5 v. symbol parameter conditions t amb = ? 40 ? cto+85 ?c unit min typ [1] max t pd propagation delay h0 to h1 and v0 to v1; see figure 8 and figure 9 [2] -3-ns t en enable time en and sel to all other outputs; see figure 10 and figure 11 -15-ns t dis disable time en and sel to all other outputs; see figure 10 and figure 11 -5-ns t b-m break-before-make time see figure 12 -10-ns t sk(o) output skew time skew between any rn, gn and bn ports; see figure 8 [3] -50-ps measurement points are given in table 11 . t sk(o) = ?? t plh1 ? t plh2 ? . fig 8. test circuit for measuring propagation delay times 001aan180 input output 1 t plh t phl v i gnd v m v m v m v oh output 2 v ol v m v m v m v oh v ol table 11. measurement points input output v m v i v x v m 0.5v cc(a) gnd to v cc(a) 0.9v oh 0.5v cc(b)
nx5dv4885e all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 4 november 2011 11 of 20 nxp semiconductors nx5dv4885e dual supply 1-of-2 vga switch test data is given in table 12 . definitions: dut = device under test. r t = termination resistance should be equal to output impedance z o of the pulse generator. c l = load capacitance including test jig and probe. r l = load resistance. fig 9. test circuit for measuring propagation delay times 001aan183 v cc v i v o dut c l r t g r l table 12. test data input load t r , t f c l r l ? 2.5 ns 10 pf 1 k ? measurement points are given in table 11 . logic level: v oh is typical output voltage level that occurs with the output load. fig 10. enable and disable times v i v m v x t dis t dis t en t en v x v x v x v m v oh gnd en, sel input output off to high high to off output high to off off to high gnd v oh gnd 001aan181
nx5dv4885e all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 4 november 2011 12 of 20 nxp semiconductors nx5dv4885e dual supply 1-of-2 vga switch a. en to switch outputs b. sel to switch outputs test data is given in table 13 . x0 refers to r0, g0, b0, scl0 or sda0 x1 refers to r1, g1, b1, scl1 or sda1 x2 refers to r2, g2, b2, scl2 or sda2 fig 11. test circuit for measuring enable and disable times 001aan184 r l sel gnd en x0 x1 x2 v cc(a) v cc(b) v i v ih or v il c l g v v o v ext = 1 v switch 1 2 001aan185 r l sel gnd en x0 x1 x2 v cc(a) v cc(b) v i v ih c l g v v o v ext = 1 v switch 1 2 table 13. test data input load t r , t f v i c l r l ? 2.5 ns gnd to v cc(a) 10 pf 100 ?
nx5dv4885e all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 4 november 2011 13 of 20 nxp semiconductors nx5dv4885e dual supply 1-of-2 vga switch a. test circuit b. input and output measurement points test data is given in table 13 . x0 refers to r0, g0, b0, scl0 or sda0 x1 refers to r1, g1, b1, scl1 or sda1 x2 refers to r2, g2, b2, scl2 or sda2 fig 12. test circuit for measuri ng break-before-make timing 001aan182 r l sel gnd en x0 x1 v ih x2 v cc(a) v cc(b) v i c l g v v o v ext = 1 v 001aag572 v i t b-m v o 0.9v o 0.9v o 0.5v i
nx5dv4885e all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 4 november 2011 14 of 20 nxp semiconductors nx5dv4885e dual supply 1-of-2 vga switch 13. additional dynamic characteristics [1] f i is biased at 0.5v cc . 13.1 test circuits table 14. additional dynamic characteristics v cc(b) = 5.0 v ? 10 %, v cc(a) = 2 v to 5.5 v, unless otherwise specified; voltages are referenced to gnd (ground = 0 v) symbol parameter conditions t amb = ? 40 ? cto+85 ?c unit min typ max f ( ?? 3db) ? 3 db frequency response r l =50 ? ; see figure 13 [1] -850-mhz ? ins insertion loss f i = 1 mhz; r l =r s = 50 ? ;see figure 13 -0.6-db xtalk crosstalk between switches; f i =50mhz; r l =50 ? ;see figure 13 [1] - ? 50 - db insertion loss is measured between r0 and r1 or r2 on each switch; crosstalk is measured from one channel to the other channel. fig 13. test circuit for measuring crosstalk and insertion loss 001aao281 nx5dv4885e v i f i 50 50 50 50 50 r0, g0, b0 v o r2, g2, b2 v cc(b) v cc(a) sel r1, g1, b1 gnd measurement network analyzer reference gnd or v cc 5 v 10 nf
nx5dv4885e all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 4 november 2011 15 of 20 nxp semiconductors nx5dv4885e dual supply 1-of-2 vga switch 14. application information the nx5dv4885e provides the level shifting necessary to drive two standard vga ports from a graphic controller as low as 2.2 v. internal buffers drive the hsync and vsync signals to vga standard ttl levels. the ddc multiplexer provides level shifting by clamping signals to a diode drop below the voltage applied on v cc(a) (see figure figure 14 ). connect v cc(a) to 3.3 v for normal operation, or to v cc(b) to disable voltage clamping for ddc signals fig 14. typical operating circuit 3 2 2 001aao282 +3.3 v r0, b0, g0 h0, v0 sda0, scl0 en +3.3 v gnd or v cc sel +5.0 v gnd r1, b1, g1 sda1, scl1 h1, v1 r2, b2, g2 sda2, scl2 vga port vga port2 graphics controller 0.1 f 0.1 f v cc(a) v cc(b) 3 2 2 3 2 2
nx5dv4885e all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 4 november 2011 16 of 20 nxp semiconductors nx5dv4885e dual supply 1-of-2 vga switch 15. package outline fig 15. package outline sot616-3 (hvqfn24) 0.5 1 0.2 a 1 e h b unit y e references outline version european projection issue date iec jedec jeita mm 4.1 3.9 d h 2.75 2.45 y 1 4.1 3.9 2.75 2.45 e 1 2.5 e 2 2.5 0.30 0.18 c 0.05 0.00 0.05 0.1 dimensions (mm are the original dimensions) sot616-3 mo-220 04-11-19 05-03-10 - - - - - - 0.5 0.3 l 0.1 v 0.05 w 0 2.5 5 mm scale sot616-3 hvqfn24: plastic thermal enhanced very thin quad flat package; no leads; 24 terminals; body 4 x 4 x 0.85 mm a (1) max. a a 1 c detail x y y 1 c e l e h d h e e 1 b 712 24 19 18 13 6 1 x d e c b a e 2 terminal 1 index area terminal 1 index area ac c b v m w m 1/2 e 1/2 e e (1) note 1. plastic or metal protrusions of 0.075 mm maximum per side are not included. d (1)
nx5dv4885e all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 4 november 2011 17 of 20 nxp semiconductors nx5dv4885e dual supply 1-of-2 vga switch 16. abbreviations 17. revision history table 15. abbreviations acronym description cdm charged device model ddc display data channel esd electrostatic discharge hbm human body model kvm keyboard video mouse mm machine model rgb red green blue spdt single pole double throw ttl transistor-transistor logic vesa video electronics standards association table 16. revision history document id release date data sheet status change notice supersedes nx5dv4885e v.2 20111104 product data sheet - nx5dv4885e v.1 modifications: ? legal pages updated. nx5dv4885e v.1 20110719 product data sheet - -
nx5dv4885e all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 4 november 2011 18 of 20 nxp semiconductors nx5dv4885e dual supply 1-of-2 vga switch 18. legal information 18.1 data sheet status [1] please consult the most recently issued document before initiating or completing a design. [2] the term ?short data sheet? is explained in section ?definitions?. [3] the product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple device s. the latest product status information is available on the internet at url http://www.nxp.com . 18.2 definitions draft ? the document is a draft versi on only. the content is still under internal review and subject to formal approval, which may result in modifications or additions. nxp semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall hav e no liability for the consequences of use of such information. short data sheet ? a short data sheet is an extract from a full data sheet with the same product type number(s) and title. a short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. for detailed and full information see the relevant full data sheet, which is available on request vi a the local nxp semiconductors sales office. in case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. product specification ? the information and data provided in a product data sheet shall define the specification of the product as agreed between nxp semiconductors and its customer , unless nxp semiconductors and customer have explicitly agreed otherwis e in writing. in no event however, shall an agreement be valid in which the nxp semiconductors product is deemed to offer functions and qualities beyond those described in the product data sheet. 18.3 disclaimers limited warranty and liability ? information in this document is believed to be accurate and reliable. however, nxp semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. in no event shall nxp semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. notwithstanding any damages that customer might incur for any reason whatsoever, nxp semiconductors? aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the terms and conditions of commercial sale of nxp semiconductors. right to make changes ? nxp semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. this document supersedes and replaces all information supplied prior to the publication hereof. suitability for use ? nxp semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an nxp semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. nxp semiconductors accepts no liability for inclusion and/or use of nxp semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer?s own risk. applications ? applications that are described herein for any of these products are for illustrative purpos es only. nxp semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. customers are responsible for the design and operation of their applications and products using nxp semiconductors products, and nxp semiconductors accepts no liability for any assistance with applications or customer product design. it is customer?s sole responsibility to determine whether the nxp semiconductors product is suitable and fit for the customer?s applications and products planned, as well as fo r the planned application and use of customer?s third party customer(s). customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. nxp semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer?s applications or products, or the application or use by customer?s third party customer(s). customer is responsible for doing all necessary testing for the customer?s applic ations and products using nxp semiconductors products in order to av oid a default of the applications and the products or of the application or use by customer?s third party customer(s). nxp does not accept any liability in this respect. limiting values ? stress above one or more limiting values (as defined in the absolute maximum ratings system of iec 60134) will cause permanent damage to the device. limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the recommended operating conditions section (if present) or the characteristics sections of this document is not warranted. constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. terms and conditions of commercial sale ? nxp semiconductors products are sold subject to the gener al terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms , unless otherwise agreed in a valid written individual agreement. in case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. nxp semiconductors hereby expressly objects to applying the customer?s general terms and conditions with regard to the purchase of nxp semiconducto rs products by customer. no offer to sell or license ? nothing in this document may be interpreted or construed as an offer to sell products t hat is open for acceptance or the grant, conveyance or implication of any lic ense under any copyrights, patents or other industrial or intellectual property rights. export control ? this document as well as the item(s) described herein may be subject to export control regulations. export might require a prior authorization from competent authorities. document status [1] [2] product status [3] definition objective [short] data sheet development this document contains data from the objecti ve specification for product development. preliminary [short] data sheet qualification this document contains data from the preliminary specification. product [short] data sheet production this document contains the product specification.
nx5dv4885e all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 2 ? 4 november 2011 19 of 20 nxp semiconductors nx5dv4885e dual supply 1-of-2 vga switch non-automotive qualified products ? unless this data sheet expressly states that this specific nxp semicon ductors product is automotive qualified, the product is not suitable for automotive use. it is neither qualified nor tested in accordance with automotive testing or application requirements. nxp semiconductors accepts no liabili ty for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. in the event that customer uses t he product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without nxp semiconductors? warranty of the product for such automotive applicat ions, use and specifications, and (b) whenever customer uses the product for automotive applications beyond nxp semiconductors? specifications such use shall be solely at customer?s own risk, and (c) customer fully indemnifies nxp semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive app lications beyond nxp semiconductors? standard warranty and nxp semiconduct ors? product specifications. 18.4 trademarks notice: all referenced brands, produc t names, service names and trademarks are the property of their respective owners. 19. contact information for more information, please visit: http://www.nxp.com for sales office addresses, please send an email to: salesaddresses@nxp.com
nxp semiconductors nx5dv4885e dual supply 1-of-2 vga switch ? nxp b.v. 2011. all rights reserved. for more information, please visit: http://www.nxp.com for sales office addresses, please se nd an email to: salesaddresses@nxp.com date of release: 4 november 2011 document identifier: nx5dv4885e please be aware that important notices concerning this document and the product(s) described herein, have been included in section ?legal information?. 20. contents 1 general description . . . . . . . . . . . . . . . . . . . . . . 1 2 features and benefits . . . . . . . . . . . . . . . . . . . . 1 3 applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 4 ordering information . . . . . . . . . . . . . . . . . . . . . 2 5 marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 6 functional diagram . . . . . . . . . . . . . . . . . . . . . . 2 7 pinning information . . . . . . . . . . . . . . . . . . . . . . 3 7.1 pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 7.2 pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 8 functional description . . . . . . . . . . . . . . . . . . . 4 8.1 rgb switches . . . . . . . . . . . . . . . . . . . . . . . . . . 4 8.2 h-sync/v-sync level translator . . . . . . . . . . . . . 4 8.3 display-data channel multiplexer . . . . . . . . . . 5 9 limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 5 10 recommended operating conditions. . . . . . . . 6 11 static characteristics. . . . . . . . . . . . . . . . . . . . . 6 11.1 test circuits and waveforms . . . . . . . . . . . . . . . 7 12 dynamic characteristics . . . . . . . . . . . . . . . . . 10 12.1 test circuits and waveforms . . . . . . . . . . . . . . 10 13 additional dynamic characteristics . . . . . . . . 14 13.1 test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 14 application information. . . . . . . . . . . . . . . . . . 15 15 package outline . . . . . . . . . . . . . . . . . . . . . . . . 16 16 abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 17 17 revision history . . . . . . . . . . . . . . . . . . . . . . . . 17 18 legal information. . . . . . . . . . . . . . . . . . . . . . . 18 18.1 data sheet status . . . . . . . . . . . . . . . . . . . . . . 18 18.2 definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 18.3 disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 18.4 trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 19 19 contact information. . . . . . . . . . . . . . . . . . . . . 19 20 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

▲Up To Search▲

Price & Availability of NX5DV4885EHF

	To Download NX5DV4885EHF Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .